BANDO INDUSTRIAL BELTS
Bando industrial belts are a superb solution for power transmission between shafts that are not axially aligned. Belts run smoothly with little noise or vibrations, and they cushion motors and bearings against load changes. They need no lubrication and require little maintenance. They have very high efficiency, usually around 95% and up to 98%. When toothed belts are used they provide excellent precision when a constant ratio between shaft rotational speeds is important.
V-belts
Adopted to solve the slippage and alignments problems that are more common with flat belts. They are an excellent combination of traction, bearing load, speed and long life. Their cross-section is actually trapezoidal, and this fits into the V on the pulley to provide a self-centering system where the belt cannot slip off. As the load increases the belt tends to bed further into the groove which increases friction and therefore torque transmission.
Toothed belts
Often used as timing belts because of their incredible efficiency. They have teeth that fit into matching teeth on the pulley. They have no slippage, run at a constant speed, and are often used for either indexing or timing purposes. Their main advantage over gears or chains is the lower noise and vibration, and the lack of a need for lubrication.
BES Transmission can supply off the shelf belts, belts cut to your specific width or spliced to your required length, or can work with you to understand your requirements and recommend appropriate solutions.
We supply:
- Round Belts
- Bancollan Round Belts (Seamless)
- Bancord Round Belts
- STS Belts PU
- High-Performance STS Belts
- HTS Belts (HTD Profile)
- King Power Synchronous Belts
- Open-End Synchronous Belts
- Super Torque Synchronous Belts
- Bancollan V-Belts
- Banflex V-Belts
Product Specification
Bando Chemical Industries is a global leader in the field of engineering rubber and plastic products.
Round Belts
Belt Description
Bando Polyurethane Round Belts (Endless) provide the following features:
- Low starting torque
- Excellent flexibility, provides smooth slip-free starts even in low temperatures
- Easy installation
- Easy to install by hand
- No re-tension needed
- Minimal tension decay
- High oil and ozone resistance
Bancollan Round Belts (Seamless)
BANDO Polyurethane Round Belts without tension members are molded and additionally ground to size and shape.
Bancord Round Belts (Open End)
BANDO Polyurehtane Round Belts are easily cut and heat-spliced to the required length.
Additional Information
| Product-type | round belt |
|---|---|
| Material | polyurethane |
| Industry | Industry |
Bancollan Round Belts (Seamless)
Belt Description
BANDO Polyurethane Round Belts without tension members are molded and additionally ground to size and shape.
These Belts stand out due to the following features:
- Low starting torques. Slip-free starts even at low temperatures.
- Easy installation
- Suitable for fixed center distance applications.
- No maintenance
- Low tension decay throughout the service life.
- High resistance to oil and ozone.
Polyurethane without tension members
| Typ | AvailableDiameter [mm] | downloadSize List |
|---|---|---|
| Round Belt Moulded | 1,6 – 2,0 – 2,5 – 3,0 – 3,5 4,0 – 5,0 |
 |
| Material | polyurethane |
|---|---|
| Product-type | round belt |
| Industry | Industry |
Bancord Round Belts (Open-End)
Belt Description
BANDO Bancord Polyurethane Round Belts (Open End) – Open-end for Heat Splicing
BANDO BANCORD round belts are offered in two compounds:
- Standard Compound 480 – 80° Shore A
- High Modulus Compound 489 – 90° Shore A
BANCORD open-end round belts are made from a polyurethane base, whose physical characteristics make it possible to heat splice the ends for a seamless version.
- Temperature resistant from -0° to +50° C
- High flexibility
- Good length stability and particularly resistant to wear
- Resistant to oil, fats and chemicals
- Particularly resistant to environmental influences like dust, dirt, ozone and atmospheric humidity.
| Typ | 1,5-2,0-2,5-3,0-3,5-4,0 | 5,0-6,0-7,0-8,0-9,0-10,0-11,0-12,0-15,0 | Download |
|---|---|---|---|
| Roll length |
200 m | 100 m | |
Hardness Standard: 80° Shore A (Compound 480)
Hardness Special: 90° Shore A (Compound 489)
Additional Information
| Material | polyurethane |
|---|---|
| Product-type | round belt |
| Industry | Industry |
STS Belts PU
Belt Description
All Super Torque Belts are made with strong, black polyurethane with fibreglass tension members.
The following advantages of Bancollan Super Torque Synchronous Belts are the result from the combination of the Super Torque profile system and the use of Polyurethane with fibreglass:
- Length stability
- Abrasion resistance (no dust)
- Precise synchronous running
- No maintenance
- Chemical resistance to oils, fats, acids and lyes
- Use in wide temperature ranges (-30°C to + 80°C, possibly higher for short durations)
- Polyurethane backing
- Fiberglass tension members
- Polyurethane teeth
| Typ | t (mm) |
H1 (mm) |
H2 (mm) |
W (mm) |
R (mm) |
|---|---|---|---|---|---|
| S2M | 2,00 | 1,40 | 0,76 | 1,30 | 1,30 |
| S3M | 3,00 | 2,00 | 1,14 | 1,95 | 1,95 |
Additional Information
| Material | polyurethane |
|---|---|
| Product-type | timing belt |
| Industry | Industry |
High Performance STS Belts
Belt Description
Description
Responding to the needs for “Energy conservation” and “High-Power transmission” on industrial machinery in recent years, Bando has developed the “High Performance STS belt”, capitalizing on our time-proven technology and experience.
Characteristics
Exceptionally high power transmission capacity:
The High Performance STS Belt achieves approximately 1.4 to 1.8 times greater power transmission than conventional STS belts.
Compact design:
The high power transmission enables belt width to be minimized, thus making system design as compact as possible.
Low noise:
The minimal belt width enables low noise operation.
Size Marks
Belt Construction
1./3. Rubber:
Synthetic rubber having less tooth deformation and a high level of hardness.
2. Tensile member:
Fibreglass tension member, with consideration for dimensional stability and flexibility.
4. Tooth canvas:
The tooth canvas has asperities on the surface and provides a low friction coefficient, accomplishing a low noise level of operation.
Furthermore, the S14M type provides two-ply tooth canvas which enables further reductions in noise levels and improved durability. The HPS-5M type is only available for clean specifications.
Dimensions & Available Sizes of Bando High-Performance STS Belts
| Typ | P | H1 | H2 | B | Download |
|---|---|---|---|---|---|
| HP-S5M | 5.00 mm | 3.61 mm | 1.91 mm | 3.25 mm | |
| HP-S8M | 8.00 mm | 5.00 mm | 3.05 mm | 5.20 mm | |
| HP-S14M | 14.00 mm | 3.70 mm | 5.30 mm | 9.10 mm | |
Additional Information
| Material | chloroprene |
|---|---|
| Product-type | timing belt |
| Industry | Industry |
HTS Belts (HTD Profile)
Belt Description
Description
The HTS tooth profile corresponds to the HTD profile.
It can be used with standard HTS pulleys
Belt Construction
- Chloprene rubber backing
- Fibreglass tensile cord
- Chloroprene rubber teeth
- Nylon fabric
Section Dimensions
Available Sizes of Bando HTS Belts (HTD Profile)
| Typ | P | H1 | H2 | Download |
|---|---|---|---|---|
| 5M | 5.0 mm | 2.1 mm | 3.6 mm | |
| 8M | 8.0 mm | 5.3 mm | 3.5 mm | |
| 14M | 14.0 mm | 10.2 mm | 6.0 mm | |
Additional Information
| Material | chloroprene |
|---|---|
| Product-type | timing belt |
| Industry | Industry |
King Power Synchronous Belts
Belt Description
Belt Description;
New technologies and materials enabled Bando to succeed in developing a new synchronous belt generation: the KPS Belt.
BANDO developed the new KPS timing belts using highly modern technology and materials. Sophisticated characteristics at low speeds and high torques open up new possibilities?for use in sectors where only chains had been used previously.
Properties;
Based on a novel construction, KPS Timing Belts offer the following product advantages:
- Up to 5 times higher transmission performance
- Space and weight savings
- Longer service life
- Use on STS SuperTorque pulleys
- Quiet running
- No maintenance
Belt Construction
Drawing
| Typ | Tooth Pitch | Download |
|---|---|---|
| KPS 8M | 8 mm | |
| KPS 14M | 14 mm | |
| Material | polyurethane |
|---|---|
| Product-type | timing belt |
| Industry | Industry |
Open-End Synchronous Belts
Belt Description
Belt Description
As with all drive elements, Bando places great emphasis on special product solutions for every kind of use in the sector of open-end belts. Thanks to this philosophy, Bando succeeded in producing open-end belts made of neoprene with fibreglass cord tension members.
Belt Construction
1) Neoprene rubber backing
2) Fibreglass tension members
3) Neoprene teeth
4) Nylon canvas
Table 1: Available Sizes of Bando Neoprene Open-End Synchronous Belts (seamless)
| Typ | Cord | Standrd belt width (Code of width) |
length range |
|---|---|---|---|
| S8M | G | 250, 500, 1000, 1500, 2000, 3000 (mm x 10) | 4,7m – 30 m |
| S14M | G | 250, 500, 1000, 1500, 2000, 3000 (mm x 10) | 4,7m – 30 m |
| H | G | 100, 200, 400, 600, 800, 1000 (Zoll x 100) | 4,7m – 30 m |
| XH | G | 100, 200, 400, 600, 800, 1000 (Zoll x 100) | 4,7m – 30 m |
| XXH | G | 100, 200, 400, 600, 800, 1000 (Zoll x 100) | 4,7m – 30 m |
Additional Information
| Material | chloroprene |
|---|---|
| Product-type | timing belt |
| Industry | Industry |
Synchronous Belts (single/double)
Belt Description
Belt Description
Bando Synchronous Belts have been applied in all industrial sectors worldwide for many years. Maximum quality requirements with respect to material and production processes guarantee the following product advantages:
Characteristics
- Synchronous running
- No maintenance
- Low storage requirements
- Space and weight savings
Belt Construction
- Neoprene rubber backing (single toothed)
- Tension members
- Neoprene-teeth
- Nylon fabric canvas
Dimension
Marking
Table 1: Available Sizes of Bando toothed belts (single/double)
| Typ | t (mm) |
t (inch) |
H1 (mm) |
H2 (mm) |
W (mm) |
ß° (angle) |
Download |
|---|---|---|---|---|---|---|---|
| MXL | 2,032 | 0,08 | 1,10 | 0,51 | 0,76 | 40 | |
| XL | 5,080 | 1/5 | 2,25 | 1,25 | 1,35 | 40 | |
| L | 9,525 | 3/8 | 3,50 | 1,90 | 3,20 | 40 | |
| H | 12,700 | 1/2 | 4,30 | 2,30 | 4,40 | 40 | |
| XH | 22,225 | 7/8 | 11,30 | 6,30 | 8,00 | 40 | |
| XXH | 31,750 | 1 1/4 | 15,80 | 9,60 | 12,20 | 40 | |
| DXL | 5,080 | 1/5 | 3,00 | 1,25 | 1,35 | 40 | |
| DL | 9,525 | 3/8 | 4,55 | 1,90 | 3,20 | 40 | |
| DH | 12,700 | 1/2 | 5,95 | 2,30 | 4,40 | 40 | |
Additional Information
| Material | chloroprene |
|---|---|
| Product-type | timing belt |
| Industry | Industry |
Super Torque Synchronous Belts
Belt Description
Belt Description
BANDO STS Super Torque Belts were developed especially for very high requirements as to power transmission, running characteristics (minimization of the polygon effect, noise reduction) and drive precision.
STS Super Torque belts offer the following product advantages:
Characteristics
- Transmission of higher torques
- Quiet running
- Longer service life
- Increased precision
- No maintenance
Belt Construction
Double-Cog STS Belt
Single-Cog STS Belt
1. neoprene backing, 2. tension member, 3. neoprene tooth, 4. nylon-fabric
1. Neoprene rubber backing (single toothed)
The tensile members are hermetically enclosed by the durable and flexible backing. It is made of strong, resistant and very thin neoprene rubber protecting the tensile members from oil, humidity and wear through friction.
2. Tension members
The tensile members consist of constantly helically wound glass fibre resulting in high tensile strength and flexibility.
3. Neoprene teeth
The teeth are made from a moderately tough, shear resistant and robust neoprene compound vulcanised as a unit with the neoprene-backing.
4. Nylon fabric canvas
The teeth are covered by a tough and very wear resistant Nylon-fabric canvas protecting the teeth against wear. The material has a very low friction coefficient thus additionally supporting the good running characteristics of the Bando STS Synchronous Belts. The clean canvas used for S1.5M, S2M and S3M belts clearly reduces rubber dust.
Standards Sizes
Table 1: Available Sizes of Bando High Performance STS Belts
| Typ | t(mm) | H1(mm) | H2(mm) | W(mm) | R(mm) | Download |
|---|---|---|---|---|---|---|
| S1.5M | 1,5 | 1,2 | 0,57 | 0,98 | 0,98 | |
| S2M | 2,00 | 1,31 | 0,76 | 1,30 | 1,30 | |
| S3M | 3,00 | 2,10 | 1,14 | 1,95 | 1,95 | |
| S4,5M | 4,50 | 2,70 | 1,71 | 2,93 | 2,93 | |
| S5M | 5,00 | 3,61 | 1,91 | 3,25 | 3,25 | |
| S8M | 8,00 | 5,30 | 3,05 | 5,20 | 5,20 | |
| S14M | 14,00 | 10,20 | 5,30 | 9,10 | 9,10 | |
| DS2M | 2,00 | 1,90 | 0,76 | 1,30 | 1,30 | |
| DS3M | 3,00 | 2,80 | 1,14 | 1,95 | 1,95 | |
| DS4,5M | 4,50 | 3,95 | 1,71 | 2,93 | 2,93 | |
| DS5M | 5,00 | 4,67 | 1,91 | 3,25 | 3,25 | |
| DS8M | 8,00 | 7,30 | 3,05 | 5,20 | 5,20 | |
| DS14M | 14,00 | 12,85 | 5,30 | 9,10 | 9,10 | |
Additional Information
| Material | chloroprene |
|---|---|
| Product-type | timing belt |
| Industry | Industry |
Synchronous Belts (Single/Double)
Belt Description
Bancollan Timing Belts from highly durable polyurethane with steel cords are used in all industrial sectors.
- Synchronous running
- Length stability
- High rate of efficiency (up to 98 %)
- No maintenance
- Chemical resistance to oils, fats, acids and lyes
- Wide operating temperature range (-30°C to + 70°C, possibly higher for a short time)
- Polyurethane backing
- Standard tension members
MXL, DMXL = Kevlar cord
all others = steel cord - Polyurethane teeth
Table 1: Available Sizes of Bando Bancollan Timing Belts (single/double)
| Typ | t (mm) |
H1 (mm) |
H2 (mm) |
W (mm) |
s° (angle) |
Download |
|---|---|---|---|---|---|---|
| T2,5 | 2,50 | 1,30 | 0,70 | 1,00 | 40 | |
| T5 | 5,00 | 2,20 | 1,20 | 1,80 | 40 | |
| T10 | 10,00 | 4,50 | 2,50 | 3,50 | 40 | |
| MXL | 2,032 | 1,20 | 0,51 | 0,76 | 40 | |
| XL | 5,080 | 2,25 | 1,25 | 1,35 | 40 | |
| L | 9,525 | 3,50 | 1,90 | 3,20 | 40 | |
| Typ | t (mm) |
H1 (mm) |
H2 (mm) |
W (mm) |
s° (angle) |
Download |
|---|---|---|---|---|---|---|
| DT5 | 5,00 | 3,30 | 1,20 | 1,80 | 40 | |
| DT10 | 10,00 | 6,80 | 2,50 | 3,50 | 40 | |
| Typ | t (mm) |
H1 (mm) |
H2 (mm) |
W (mm) |
s° (angle) |
Download |
|---|---|---|---|---|---|---|
| DMXL | 2,032 | 1,53 | 0,51 | 0,76 | 40 | |
| DXL | 5,080 | 3,01 | 1,25 | 1,35 | 50 | |
Additional Information
| Material | polyurethane |
|---|---|
| Product-type | timing belt |
| Industry | Industry |
Synchronous Belts endless
Belt Description
Belt Description
Bando produces open-end synchronous belts out of polyurethane with steel or aramid cord, placing particular emphasis on special product solutions for every kind of use in the open-end synchronous belts sector.
Open-end belts can be supplied ex stock in desired lengths up to the maximum roll length (please see table below)
The jointed version can be supplied in desired lengths, taking into account minimum length requirements.
Table 1: Available Sizes of Bando Bancollan Long Synchronous / STS Belts (LSB-U), Cord: W = Steel; K = Aramid
| Typ | Standard – Cord |
Special Cord |
Standard belt width (code of width) |
max. width (mm) |
max. length (Meter) |
jointable |
|---|---|---|---|---|---|---|
| T5 | W | K | 6, 10, 16, 25, 32, 48, 50 | 50 | 50 | yes |
| T10 | W | K | 16, 25, 32, 50, 75, 96, 100 | 100 | 50 | yes |
| AT5 | W | K | 10, 16, 25, 32, 50 | 50 | 100 | yes |
| AT10 | W | K | 16, 25, 32, 50, 75, 96, 100 | 100 | 100 | yes |
| S2M | W | – | 50, 100, 150, 200, 250, 300, 350, 400 | 40 | 60 | no |
| S3M | W | – | 60, 120, 180, 240, 300, 360, 420, 480 | 48 | 60 | no |
| S8M | K | W | 150, 200, 250, 300, 400, 500, 750, 1000 | 100 | 30 | no |
| XL | W | K | 025, 031, 037, 050, 075, 100, 150, 200 | 50,8 | 50 | yes |
| L | W | K | 037, 050, ,075, 100, 150, 200 | 50,8 | 50 | yes |
| H | W | K | 050, 075, 100, 150, 200, 300, 400 | 101,6 | 50 | yes |
Additional Information
| Material | polyurethane |
|---|---|
| Product-type | timing belt |
| Industry | Industry |
TN Synchronous Belts
Belt Description
Belt Description
Bancollan TN Synchronous Belts, made from highly durable polyurethane, were developed especially for very small drives. TN Synchronous Belts are high-precision and extra light-duty, with a unique profile.
TN Synchronous Belts offer the following product advantages:
- Minimization of construction space
- Minimum pulley size 5 mm with TN10; 7 mm with TN15
- High torque at low pre-tension
- Low distortion and smooth running
- Very small pitch and optimized grip in the pulley grooves guarantee smooth revolutions with accurate speed just like a flat belt
- No backslash
- Precise positioning
- Choice of tension members according to respective application
- Polyurethane backing
- Tension members
(Steel wire, Aramid or Polyester) - Polyurethane teeth
Table 1: Available Sizes of Bando Bancollan TN Synchronous Belts
| Typ | t (mm) |
H1 (mm) |
H2 (mm) |
TEnsiONMember | Code | Download | |
|---|---|---|---|---|---|---|---|
| TN10 | 1,00 | 0,85 | 0,44 | – Polyester (Tetron) | T | |
|
| TN15 | 1,50 | 1,30 | 0,70 | – Aramid – Polyester (Tetron) – Steel (from 79 TN15) |
K T W |
|
Additional Information
| Material | polyurethane |
|---|---|
| Product-type | timing belt |
| Industry | Industry |
Bancollan V-BELTS
Belt Description
There are two types of BANCOLLAN V-Belts from high quality POLYURETHANE:
VC Single Cogged Type
DC Double Cogged Type
Pulleys of 16 mm diameter and upwards can be used due to the belts very high flexibility. The cast belt profile shows very narrow tolerances, which leads to a very smooth running. Due to the use of polyurethane the drive remains “clean“ compared to rubber V-belts. High resistance to oil, fats and chemicals are further advantages of BANCOLLAN V-Belts.
- Temperature resistant from -30° to +70°C
- High resistance to oil, fats and chemicals
- Low vibration belt running
- Low noise
- Clean operation: No ?black rubber dust“ problem.
- Polyester tension members
- Polyurethane belt structure and backing
| Section | Top width bo [mm] |
Thickness h [mm] |
Angle[ ° ] | Download |
|---|---|---|---|---|
| VC – 6 | 6,0 | 4,0 | 40 | |
| DC – 6 | 6,0 | 4,0 | 40 | |
Additional Information
| Material | polyurethane |
|---|---|
| Product-type | v-belt |
| Industry | Industry |
BANFLEX Scrum banded V-Belts
Belt Description
Banded BANFLEX SCRUM polyurethane V-belts were developed especially for high speed drives with a belt speed of up to 60 m/s.
The ground flanks and enlarged profile angle provide for extremely low vibration running. Small pulley diameters and higher belt speeds permit compact and light drives. Ideal for horizontal drives. The use of polyurethane makes the belt highly resistant to oil and ozone. The diagonally grooved back of the belt optimizes its flexibility.
- Temperature resistant from -30° to +60°C
- High oil resistance
- Highly resistance to environmental influences like heat, ozone, sunlight and effects of the weather.
- Polyurethane belt backing
- Banded polyester canvas
- Polyester tension members
- Polyurethane belt structure
| Section / number of ribs |
Top width bo [mm] |
Thickness h [mm] |
Angle[ ° ] | Download |
|---|---|---|---|---|
| 2- 5MS | 9,80 | 3,30 | 69 | |
| 3- 5MS | 15,10 | 3,30 | 69 | |
| 2- 7MS | 15,60 | 5,30 | 68 | |
| 3- 7MS | 24,10 | 5,30 | 68 | |
| 2- 11MS | 24,40 | 7,00 | 68 | |
| 3- 11MS | 37,60 | 7,00 | 68 | |
Additional Information
| Material | polyurethane |
|---|---|
| Product-type | v-belt |
| Industry | Industry |
Banflex V-Belts
Belt Description
Banded BANFLEX belts from polyurethane were developed especially for high speed drives with a belt speed of up to 60 m/s, with extremely low vibration running.
Small pulley diameters and higher belt speeds permit compact and light drives. The use of polyurethane makes the belt highly resistant to oil and ozone. The diagonally grooved back of the belt optimizes its flexibility.
- Temperature resistant from -30° to +60°C
- High oil resistance
- High resistance to environmental influences like heat, ozone, sunlight and effects of the weather.
- Polyurethane belt backing
- Polyester tension members
- Polyurethane belt structure
| Section / number of ribs |
Top width bo [mm] |
Thickness h [mm] |
Angle[ ° ] | Download |
|---|---|---|---|---|
| 3M | 3,0 | 2,1 | 69 | |
| 5M | 5,0 | 3,3 | 69 | |
| 7M | 7,0 | 5,3 | 68 | |
| 11M | 11,0 | 6,9 | 68 | |
Additional Information
| Material | polyurethane |
|---|---|
| Product-type | v-belt |
| Industry | Industry |
